:
from
to
Clear
Clear
ACE BACKSTAGE 322SLSS Full Pocket/Standard SS Lid Stainless Steel Bezel
SKU: ACE 322SLSS
Full Stage Pocket, Standard Solid Stainless Steel Lid and Trim Bezel with Brushed Finish
ACE BACKSTAGE CO., INC. large-sized Stage Pocket, the Full Stage Pocket, is a standard general use vertical slant panel flush stage pocket. The Full Stage Pocket is made of heavy duty steel and may be used to conceal audio, communications, control, data, electric AC power, switches, video, and voice connections etc. below the floor surface for easy access and to prevent connector damage. The Full Stage Pocket has a larger capacity inter-changeable panel system which permits easy custom connector/panel configurations.
The Full Stage Pocket has the panel capacity for either:
• (2) #PNL-100 Series CONNECTRIX Panels or
• (2) #PSW-100 Series Switchcraft® Panels or
• (2) #PE Series Single Gang Electric Duplex Switch Box Panels or
• (1) #PNL-120 Series CONNECTRIX Panel
The Full Stage Pocket has the connector capacity for either:
• (12) CONNECTRIX Connectors or
• (12) Neutrik® Connectors or
• (12) Switchcraft® Connectors or
• (6) CONNECTRIX, Neutrik®, or Switchcraft® Connectors and (1) #PE Electric Duplex Switch Box
Utilizing ACE's CONNECTRIX System will allow mounting of up to 12 CONNECTRIX, Neutrik®, Switchcraft®, and/or Custom Connectors in the Full Stage Pocket. All ACE Full Stage Pockets are welded steel construction, with a 1/8" (nominally 11 ga. (.120")) thick CRS steel Lid and Mounting Flange and a 16 ga. (.062") thick Pocket Body. The Full Stage Pocket resists bending under even the most severe stage loads.
Removable spring loaded hinge pins permits easy exchange of lids for carpet lids, locking lids, standard lids, and other custom application lids. A generous cable way slot of 3/8" x 8" permits easy cable exit from the stage pocket, even for large gauge cables. A cableway slot closure channel closes the slot when not in use. The Full Stage Pocket has an easy installation into 8.5" x 8.5" cutout in the stage floor. Open easy access from top or back of the Full Stage Pocket to connector panels makes for easy installation.
A scratch/wear resistant finish, oven cured powder coat is electro-staticly applied inside and outside the entire Stage Pocket. Decorator neutral Antique Copper Vein or Textured Black finishes are standard. A Solid Brass Lid and Mounting Flange as well as Solid Stainless Steel Lid and Mounting Flange are also available by special order. The Full Stage Pocket's solid rubber Lid Stops cradle the lid to prevent lid rattle.
• Full Stage Pocket Body Size = 8.000” W x 3.500” H x 7.187” D
• Full Stage Pocket Lid & Mounting Flange Size = 10.500” W x 1.000” H x 10.500” D
• Full Stage Pocket Connector Capacity = Up to 12 CONNECTRIX, Neutrik®, or Switchcraft®
• Full Stage Pocket Cutout Dimensions = 8.500" W x 8.500" H
• Full Stage Pocket Material = CRS Steel and/or Solid Half Hard Brass
• Full Stage Pocket Panel Capacity =
• (2) #PNL-100 Series CONNECTRIX Panels OR
• (2) #PSW-100 Series Switchcraft® Panels OR
• (2) #PE Series Single Gang Electric Duplex Switch Box Panels OR
• (1) #FP3E Series Triple Gang Electric Duplex Switch Box Panel OR
• (1) #PNL-120 Series CONNECTRIX Panel
The Full Stage Pocket has the panel capacity for either:
• (2) #PNL-100 Series CONNECTRIX Panels or
• (2) #PSW-100 Series Switchcraft® Panels or
• (2) #PE Series Single Gang Electric Duplex Switch Box Panels or
• (1) #PNL-120 Series CONNECTRIX Panel
The Full Stage Pocket has the connector capacity for either:
• (12) CONNECTRIX Connectors or
• (12) Neutrik® Connectors or
• (12) Switchcraft® Connectors or
• (6) CONNECTRIX, Neutrik®, or Switchcraft® Connectors and (1) #PE Electric Duplex Switch Box
Utilizing ACE's CONNECTRIX System will allow mounting of up to 12 CONNECTRIX, Neutrik®, Switchcraft®, and/or Custom Connectors in the Full Stage Pocket. All ACE Full Stage Pockets are welded steel construction, with a 1/8" (nominally 11 ga. (.120")) thick CRS steel Lid and Mounting Flange and a 16 ga. (.062") thick Pocket Body. The Full Stage Pocket resists bending under even the most severe stage loads.
Removable spring loaded hinge pins permits easy exchange of lids for carpet lids, locking lids, standard lids, and other custom application lids. A generous cable way slot of 3/8" x 8" permits easy cable exit from the stage pocket, even for large gauge cables. A cableway slot closure channel closes the slot when not in use. The Full Stage Pocket has an easy installation into 8.5" x 8.5" cutout in the stage floor. Open easy access from top or back of the Full Stage Pocket to connector panels makes for easy installation.
A scratch/wear resistant finish, oven cured powder coat is electro-staticly applied inside and outside the entire Stage Pocket. Decorator neutral Antique Copper Vein or Textured Black finishes are standard. A Solid Brass Lid and Mounting Flange as well as Solid Stainless Steel Lid and Mounting Flange are also available by special order. The Full Stage Pocket's solid rubber Lid Stops cradle the lid to prevent lid rattle.
• Full Stage Pocket Body Size = 8.000” W x 3.500” H x 7.187” D
• Full Stage Pocket Lid & Mounting Flange Size = 10.500” W x 1.000” H x 10.500” D
• Full Stage Pocket Connector Capacity = Up to 12 CONNECTRIX, Neutrik®, or Switchcraft®
• Full Stage Pocket Cutout Dimensions = 8.500" W x 8.500" H
• Full Stage Pocket Material = CRS Steel and/or Solid Half Hard Brass
• Full Stage Pocket Panel Capacity =
• (2) #PNL-100 Series CONNECTRIX Panels OR
• (2) #PSW-100 Series Switchcraft® Panels OR
• (2) #PE Series Single Gang Electric Duplex Switch Box Panels OR
• (1) #FP3E Series Triple Gang Electric Duplex Switch Box Panel OR
• (1) #PNL-120 Series CONNECTRIX Panel